Stairlift

We put the chair stair lift with all the options. Right or turning stairs , inside or outside, standing or shell …  

Possible configurations of staircases :

Specifications chairs :

Straight chair :

* Power: Electricity single phase 220 V/10 A. near the rail.
 * Color: The frame, engine block and the seat structure are painted beige factory – gray, back and seat cushions are trimmed in beige cloth fireproof and waterproof. The rail is aluminum.
 * Load admitted: The whole load can be carried by the chair up stairs is 127 Kg
 * Bindings: The rail is fixed on the stairs with cleats and screws
 * Belt: A seat belt is supplied factory
 * Rail: aluminum comprising grooving for receiving all anchorages. The rack drive is inserted into the guide rail.
 * Seat: The seat is placed in the vertical rail to allow maximum clearance of the stairs when not in use. It can rotate 45 ° or 64 ° to facilitate the landing upstairs. The standard size is 368 (folded) x 422 mm.
 * Raises the feet: the feet poses can be modified according to the standard configuration of your staircase. It can be folded up to free up the passage on the stairs when not in use. It is equipped with a sensitive edge paired electrical contacts security stopping the movement of the seat in case of obstacles in its path. The move in the opposite direction is still possible.
 * Angle: The equipment is scheduled for a tilt angle of your stairs than 53 °.
 * Armrests: Armrests fold both sides of the seat width between armrests is 485 mm. The joystick control is placed after the event, left or right and comes with a command button to put up with light and an emergency stop.
 * Overspeed Safety: where the seat would make a descent speed exceeds the rated speed specified, a mechanical device controlled by contacts of the electrical safety device would stop to avoid the mad dash downhill.
 * Engines: The mobility of the equipment is provided by an asynchronous electric motor with four poles of a power of 280 W. equipped with an electromagnetic brake is actuated by the lack of current equipment has an electrical protection of the engine.
  * Speed: The speed of movement of the seat, both uphill or downhill, is 0.10 m / sec.
 * Controls: On one arm of the seat is a lever (joystick) to make moving the seat up or down by constant pressure, this command is of the “dead man”, by releasing the lever, seat movement is stopped immediately. To restart an outbreak of 2 to 3 seconds is necessary for the safety of users, this call is signaled by a buzzer (beep beep). A call button and sending is installed on each floor served.
 * Troubleshooting Manual: If a power outage, the 2 batteries allow 10 trips.
* Compliance with standards: The seat is fabricated staircase ascends the current European standards and is compliant with Belgian NBN 52,036 on up – stairs. You can make a check by a recognized organization.  

Chair type boom :

*Use: Transporting a passenger standing on a chair “boom” moving along a straight track mounted on a staircase, with variable angle, max 60 °, between two specified levels.
 
* Power: Electricity single phase 220 V/16 A. near the rail at the location indicated on the sketch
 * Color: The frame, engine block and the seat structure are painted beige factory – gray, back and seat cushions are filled with plastic blue, pink, green or beige with your choice. The rail is anodized aluminum.
 * Load admitted: The whole load can be carried by the chair up stairs is 125 Kg
 * Bindings: The rail is fixed on the stairs with cleats and screws
* Rail: The steel section containing the groove for receiving all the anchors. The drive rack is fixed under the guide rail.
 * Seat: The seat is placed in the vertical rail to allow maximum clearance of the stairs when not in use. It is equipped with a barrier side down. Incidentally, it can be used to transport the person sitting.
 * Laying feet: The feet poses can be modified according to the standard configuration of your staircase. It can be folded up to free up the passage on the stairs when not in use. It is equipped with a sensitive edge paired electrical contacts security stopping the movement of the seat in case of obstacles in its path. The move in the opposite direction is still possible. This poses – legs used mainly to transport the person standing.
 * Angle: The equipment is scheduled for a tilt angle of your stairs than 55 °.
 * Engines: The mobility of the equipment is ensured by an electric motor with a DC power of 250 W. equipped with an electromagnetic brake is actuated by power failure and powered through batteries.
 * Speed: The speed of movement of the seat, both uphill or downhill, is 0.089 m / sec.
 * Controls: On the fence of the seat is a command to move to the seat up or down by constant pressure, this command is of the “dead man”, by releasing the lever, the movement of the seat is stopped immediately. To restart an outbreak of 2 to 3 seconds is necessary for the safety of users, this call is signaled by a buzzer (beep beep). A call button and sending is installed on each floor served.
 * AC fail: If a power outage, it is possible to make 15 trips to complete the battery capacity.
 * Compliance with standards: The seat is fabricated staircase ascends the current European standards and is compliant with Belgian NBN 52,036 on up – stairs – and the Machinery Directive 2006/42. It can be controlled by an approved inspection body. 
 

Curve chair :

* Use: Carrying a passenger on a seat moving along a rail fixed with a curved staircase, with variable angle, max 60 °, between two floors. Key commissioning.
 * Food: Food of the Installation is done by an AC outlet (220 Vac) at one of the two floors served. The optimum location being given during the visit of a representative of our society. During his travels or absence of AC power, the motors of the chair are powered by two batteries of 12 amps that load at breakpoint top of the system and break point down. In some cases, as in the presence of rail facilities with removable intermediate support points are also existing batteries.
 * Restrictions: The proposed model is expected to be installed only within a dwelling.
 * Color: The frame, engine block and the seat structure are painted at the factory, the back, seat and armrests are cushioned synthetic fabric or anthracite, burgundy, green or beige with your choice . The rail painted steel plant can be provided without charge in three colors-brown, gray, off white.
  * Load admitted: Load to be carried by the chair up stairs may not exceed 125 Kg
 * Bindings: The rail is fixed on the steps of the staircase using appropriate brackets and screws.
 * Belt: A seat belt retractor with medical grade.
 * Rail: Steel tubular section 76 mm in diameter, including the anchoring devices. The drive rack is fixed under the guide rail to limit the risk of dirt or friction.
 * Seat: The seat is placed directly above the rail to allow maximum clearance of the stairs when not in use. It can rotate 45 °, 64 °, to facilitate the landing. The width between armrests is 438 mm.
 * Laying feet: It is foldable upwards to clear up the passage on the stairs when not in use. It is equipped with a sensitive edge paired electrical contacts security stopping the movement of the seat in case of obstacles in its path. The move in the opposite direction is still possible. It remains secured to the seat during rotation for easy exit. Poses a foot adapted to the curvature of your staircase can be studied by our company.
 * Armrests: Armrests fold both sides of the seat, the command is normally located on the right arm but the reverse is possible. A key commissioning is included with the installation.
 * Drive: The movement of the chair is provided by two electric motors with a DC power of 250 W, each fitted with an electromagnetic brake and powered through the battery. In case of failure of one engine, the other stops. One engine is equipped with an encoder that stores the path and courbures.Le doubling of the engine increases the longevity of use, enhances the ease of driving the machine, ensures safety in case of mechanical failure and minimizes noise operating the machine.
 * Speed: The speed of movement of the seat, both uphill or downhill, is on average 0.11 m / sec. The speed is controlled by the electronic card in the curves to improve the feeling of comfort.
 * Angle: The equipment is scheduled for a tilt angle of your stairs than 60 °. A leveling engine, part of standard equipment, keeping in constant head horizontal.
 * Overspeed Safety: The joint operation of two motors drive the seat to prevent the speed of the descent. This device provides a comfortable solution and replaces the mechanical device.
 * Controls: On one of the armrests of the seat is a lever (joystick) to make them move the seat upward or downward by a constant pressure. This command is like “this man”. This means that during the interruption of the action on the lever, the seat movement is stopped immediately.
 During activation of the ascent or descent of the seat, a delay of 2 to 3 seconds delay the movement of the seat. The delay in starting, indicated by a beep is needed to improve passenger safety.
 Wall controls (one per floor served) operated by infra red on the frequency of 620 MHz and does not require wiring can also turn up the descent of the chair with the same ease as the lever arm.
 The control lever on the armrest is known priority orders murals.
 * AC fail: If a power outage, it is possible to make 15 trips to complete the battery capacity.
 * Compliance with standards: The seat is fabricated staircase ascends the current European standards and is compliant with Belgian NBN 52,036 on up – stairs. It has been a type test by LIFTINSTITUT. The manufacturer is ISO 9001 (Minutes of 02.19.1998 No. 17392) Certificate TUV – BSI-EC.
* Use: Carrying a passenger on a seat moving along a rail mounted on a staircase, with variable angle between two specified levels (ground floor + first)